Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.

Don't ignore the forklift at the workplace. If the procedure is not good, there will be major mishaps in minutes, and there are lots of mishaps including forklifts.

Situation 1: The forklift freight obstructed the motorist's view, and the individual in front might not be discovered, leading to a rolling mishap.
Situation 2: In order to maintain the balance of the forklift when lifting hefty items, the staff members utilized their body weight as the weight, which nearly triggered casualties.
Situation 3: The width of the forklift cargo goes beyond the allowed size of the path and hangs on the roadside shelf, which virtually creates an mishap.
Situation 4: Forklift is speeding and surrender throughout a turn.
Situation 5: The forklift chauffeur did not notice the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift lifts the personnel unlawfully, the forklift motorist does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not wear a safety belt and fell from the lorry when it rolled over and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be secure before beginning.
3. When the forklift starts with a tons, the driver must first verify that the load is secure and trustworthy.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the job website or while driving, take care that there will be no challenges overhead. When the lots is traveling, the fork needs to not be elevated too high, which will influence the security of the forklift. .
3. After unloading, the fork must be decreased to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released initially. High-speed sharp turns are restricted. High-speed sharp turns will certainly create the vehicle to lose lateral stability and tip over. .
5. When the forklift is downhill, it is purely restricted to switch off the fire and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are special conditions.
6. When the forklift is running, it has to obey the traffic rules in the factory and should keep a specific security distance from the car in front. .
7. When the forklift is running, the tons needs to be in the lowest setting that does not impede the driving, and the gantry must be appropriately slanted back. The tons will not be increased except when stacking or loading. .
8. The height of the load must not obstruct the vehicle driver's view. In unique scenarios, when the product affects the forward vision, drive at a low rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility area is 5 km/h, and it must drive safely at a reduced speed when entering the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to base on the fork to hold products and play a balancing duty. .
12. If troubles are discovered, they will be fixed and reported in a timely manner, and they will certainly never ever operate with ailments or hide them.

loading and unloading.
1. When fork-loading things, the distance in between both forks should be readjusted as required to make the load of the two forks well balanced and not manipulated, and one side of the item need to protest the rack. .
2. It is prohibited to work with a solitary fork or utilize a fork top or draw. In special circumstances, safety and security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of filling and discharging things, the forklift needs to be stopped with the brake. .
4. The speed of the lorry must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled things and harm individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it needs to be noted that the fork pointer ought to not touch various other goods or items. The lots ought to be maintained with minimal back tilt of the gantry to ensure that the lots does not slide in reverse. The pole can be tilted ahead a little when the load is reduced to permit easy placement of the tons and removal of the forks. .
6. It is forbidden to fork goods at broadband and ram difficult things with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and injure people. .
8. Straining is restricted, and it is forbidden to use forks to lift workers to engage in high-altitude procedures to avoid high-altitude falling crashes. .
9. It is not enabled to make use of the brake inertia to slip, place, round Electric Forklift Truck for Warehouse or roll objects. .
10. It is not allowed to utilize forks to pick, transform pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork are in the air. Prior to leaving the forklift, you have to dump the goods or lower the fork structure.
2. Draw the emergency brake manage to dead or depress the hand brake switch.
3. The engine is turned off and the power is removed. (Except for special scenarios, such as the chauffeur does not leave the lorry's line of vision and does not exceed 1 min).
4. Eliminate the trick. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be checked, and gas, lubing oil and air conditioning water need to be added.
2. Inspect the safety and security efficiency of starting, running and braking.
3. Check whether the lights and horn signals are complete and efficient.
4. During the operation of the forklift, examine whether the stress and temperature level are typical.
5. After the forklift is running, the exterior leak should likewise be inspected and the seals must be changed in time.

Forklift Safety Operation Specifications.
1. You must check before leaving the auto;.
2. When you experience someone in front of you during driving, you ought to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the propensity of " cost-free switching";.
6. Adding and down the incline ought to be slow and Stand-on Electric Pallet Stacker uniform, and no activating the incline is allowed.
7. Do not drive throughout the gradient. When the gradient is greater than 10%, the vehicle needs to be driven backwards when going downhill;.
8. When the forklift workers bring the goods and move forward, if they encounter large or hefty goods and most likely to the driver's line of sight, they should take the turning around exercise
.
The "Eight Prohibitions" need to be complied with in the procedure.
1. Single fork operation is not enabled.
2. It is not allowed to raise the goods for long distance driving.
3. It is not allowed to get the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and various other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not enabled to make use of stopping force to exile round or easy-to-roll items.
7. It is not permitted to bring people to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Car parking is not permitted under the list below problems.
1. Contours, slim roads, railway crossings;.
2. Sections with a longitudinal slope above 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the section with the same length as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844